Teensy Micro SD Card Adaptor

Teensy Teensy Micro SD Card Adaptor
Click to enlarge
Price: £7.80
(£6.50 + VAT)
Availability: 18
Model: TEENSY-SD
Manufacturer: Teensy
Average Rating: Not Rated

Teensy

Teensy Micro SD Card Adaptor

This Micro SD card adaptor allows you to easily use gigabytes of flash memory with Teensy. It can also be used on a breadboard, or with almost any AVR processor.

A 3.3 volt regulator and 5 to 3.3 volt buffer chip protects the SD card, and allows interfacing to 5 volt processors

Teensy++ Connections

The SD adaptor can be used on Teensy++, with 4 pins and 2 wires.

Use on Teensy 3.0 and 3.1

The very first thing to do is solder the 3V pads on the bottom of the MicroSD adapter.

This is because Teensy 3 = 3.3v, while other/older Teensy's are 5v.

The MicroSD adapter can work at both voltages, all that is required is to connect 2 pads together to set it to 3.3v:

Then you need to wire it up in the following manner

+5V goes to 3.3V (100 mA max)
Ground goes to GND
MOSI goes to pin 11, DOUT
MISO goes to pin 12, DIN
SCLK goes to pin 13, SCK
SS goes to pin 10, CS

Software Support

Teensyduino supports SD cards for USB communication. Select it from the Tools->USB Type menu after installing.

Several Arduino libraries support access to SD cards.

The SdFat library has been tested and is known to work on Teensy 2.0 and Teensy++ 2.0 with this SD adaptor.

Switch (SW) Pin

The flash socket has a switch that can detect when a card is inserted. Normally SW is not used. Most projects don't need this pin, and nearly all SD libraries just check for the card by communicating with it rather than requiring an extra pin.

But if you design your code for a switch, or use someone else's code that requires a switch, the option is there. The switch connects to an an unpopulated resistor, so a low-value resistor or jumper wire needs to be soldered in place to enable access to the switch.

The switch might also be useful in special cases, like perhaps a battery powered project that waits for a card to be inserted. The pin change interrupts can wake the processor from a deep sleep mode, which would save battery life compared to regularly polling to see if a card has appeared.

 

Teensy 3.6
Teensy 3.6
TEENSYV36
£33.60    
5 out of 5 Stars!
Breakout Board for microSD Flash Drive
Breakout Board for microSD Flash Drive
MICROSD-BASIC
£4.20    
Teensy 3.2
Teensy 3.2
TEENSYV32
£19.80    
5 out of 5 Stars!
Teensy LC
Teensy LC
TEENSY-LC
£10.74    
5 out of 5 Stars!
Teensy WIZ820IO Ethernet & Micro SD Card Adaptor
Teensy WIZ820IO Ethernet & Micro SD Card Adaptor
WIZ820_SD_ADAPTOR
£6.00    
4GB Micro SD Memory Card
4GB Micro SD Memory Card
4GB-USD
£4.80    
Teensy ++ 2.0
Teensy ++ 2.0
TEENSY++2
£24.00    
Teensy 3.5
Teensy 3.5
TEENSYV35
£26.40    
Write Review
Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad            Good

Enter the code in the box below:

Teensy Micro SD Card Adaptor
Click to enlarge
Teensy Micro SD Card Adaptor
Click to enlarge
Teensy Micro SD Card Adaptor
Click to enlarge
Teensy Micro SD Card Adaptor
Click to enlarge
Teensy Micro SD Card Adaptor
$ 7.80 New In Stock
Shopping Cart
0 items
 
DELIVERY/PAYMENT

Free Delivery Orders over £50

UK - £2.40 orders under £50
Airmail from £2.95 (+VAT)
More Details...

 
Brands
 
 Check out our videos