Pololu 12V, 1A Step-Down Voltage Regulator D24V10F12

The compact (0.5″ × 0.7″) D24V10F12 synchronous step-down (or buck) voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 12 V while allowing for a maximum output current of 1A. This regulator offers typical efficiencies between 85% and 93% and has a very low dropout, so it can be used with input voltages as low as a few hundred millivolts above 12 V. The pins have a 0.1″ spacing, making this board compatible with standard solderless breadboards and perfboards.

Features the Intersil ISL85410 1A synchronous step-down regulator and generates lower output voltages from input voltages as high as 36 V. It is a switching regulator (also called switched-mode power supplies (SMPS) or DC-to-DC converters) with typical efficiencies between 80% and 93%, which is much more efficient than linear voltage regulators, especially when the difference between the input and output voltage is large. Thi regulators have a power-save mode that activates at light loads and a low quiescent (no load) current draw, which make it well suited for applications that are run from a battery.

The SHDN pin can be used to put the board in a low-power state that reduces the quiescent current to approximately 10 µA to 20 µA per volt on VIN, and a PG (power good) output can be used to monitor the state of the regulator’s output voltage.

The D24V10F12 regulator feature short-circuit/over-current protection, and thermal shutdown helps prevent damage from overheating. Does NOT have reverse-voltage protection.

Features

  • Input voltage:
    • [output voltage + dropout voltage] to 36V (see below for more information on dropout voltage)
  • Fixed 12 V output with 4% accuracy
  • Maximum output current: 1 A
  • Typical efficiency of 80% to 93%
  • 500 kHz switching frequency (when not in power-save mode)
  • 2 ms soft-start reduces in-rush current on power-up
  • 200 μA typical no-load quiescent current
  • Integrated over-temperature and over-current shutoff
  • Small size: 0.7″ × 0.5″ × 0.14″ (18 mm × 13 mm × 3.5 mm)

Using the regulator

Connections

The buck regulator has five connections: power good (PG). shutdown (SHDN), input voltage (VIN), ground (GND), and output voltage (VOUT).

The “power good” indicator, PG, is an open-drain output that drives low when the regulator’s output voltage falls below 80% or rises above 120% of its target output voltage. This output is also actively held low for the duration of the regulator’s 2 ms soft-start period and while the regulator is being disabled by the SHDN input or by over-temperature or over-current fault conditions. An external pull-up resistor is generally required to use this pin.

The SHDN pin can be driven low (under 0.4 V) to turn off the output and put the board into a low-power state. There is a 100 kΩ pull-up resistor between the SHDN pin and VIN, so if you want to leave the board permanently enabled, the SHDN pin can be left disconnected. While the SHDN pin is being driven low, the current draw of the regulator is dominated by the current through the pull-up resistor and will be proportional to the input voltage. (At 36 V in it will draw about 360 μA.)

The input voltage, VIN, powers the regulator. Voltages between 3 V and 36 V can be applied to VIN, but the effective lower limit of VIN is VOUT plus the regulator’s dropout voltage, which varies approximately linearly with the load (see below for graphs of dropout voltages as a function of the load). Additionally, please be wary of destructive LC spikes (see below for more information).

The output voltage, VOUT, is fixed at 12 V.

The five connections are labeled on the back side of the PCB and are arranged with a 0.1″ spacing along the edge of the board for compatibility with solderless breadboards, connectors, and other prototyping arrangements that use a 0.1″ grid. You can solder wires directly to the board or solder in either the 5×1 straight male header strip or the 5×1 right-angle male header strip that is included.

Efficiency and Dropout Voltage Graphs

The efficiency of a voltage regulator, defined as (Power out)/(Power in), is an important measure of its performance, especially when battery life or heat are concerns. This family of switching regulators typically has an efficiency of 80% to 93%, though the actual efficiency in a given system depends on input voltage, output voltage, and output current. See the efficiency graph near the bottom of this page for more information.

In order to achieve a high efficiency at low loads, this regulator automatically goes into a power-save mode where the switching frequency is reduced. In power-save mode, the switching frequency of the regulator changes as necessary to minimize power loss. This could make it harder to filter out noise on the output caused by switching.

Typical dropout voltage

The dropout voltage of a step-down regulator is the minimum amount by which the input voltage must exceed the regulator’s target output voltage in order to ensure the target output can be achieved. For example, if a 5 V regulator has a 1 V dropout voltage, the input must be at least 6 V to ensure the output is the full 5 V. Generally speaking, the dropout voltage increases as the output current increases.

The graphs below show the typical efficiency and dropout voltage of the 12V D24V10F12 regulator as a function of the output current:

Regulator Efficiency


Dropout Voltage

Schematic diagram

Schematic diagram

Low Voltage Spikes

When connecting voltage to electronic circuits, the initial rush of current can cause voltage spikes that are much higher than the input voltage. If these spikes exceed the regulator’s maximum voltage (36 V), the regulator can be destroyed. In tests with typical power leads (~30″ test clips), input voltages above 20 V caused spikes over 36 V.

If you are connecting more than 20 V or your power leads or supply has high inductance, we recommend soldering a 33 μF or larger electrolytic capacitor close to the regulator between VIN and GND. The capacitor should be rated for at least 50 V.

Write a review

Please login or register to review

Pololu 12V, 1A Step-Down Voltage Regulator D24V10F12

  • Manufacturer: Pololu
  • Product Code: D24V10F12
  • Availability:  45
  • £6.24

  • Ex Tax: £5.20

Pololu

Related Products

5V, 300mA Step-Down Voltage Regulator D24V3F5

5V, 300mA Step-Down Voltage Regulator D24V3F5

5V, 300mA Step-Down Voltage Regulator D24V3F5 The compact (0.4"×0.5") D24V3F5..

£4.20 Ex Tax: £3.50

3.3V, 300mA Step-Down Voltage Regulator D24V3F3

3.3V, 300mA Step-Down Voltage Regulator D24V3F3

3.3V, 300mA Step-Down Voltage Regulator D24V3F3 The compact (0.4"×0.5") D24V3..

£3.00 Ex Tax: £2.50

5V Step-Up/Step-Down Voltage Regulator S7V7F5

5V Step-Up/Step-Down Voltage Regulator S7V7F5

5V Step-Up/Step-Down Voltage Regulator S7V7F5 The S7V7F5 switching step-up/step-down regulato..

£4.56 Ex Tax: £3.80

3.3V Step-Up/Step-Down Voltage Regulator S7V8F3

3.3V Step-Up/Step-Down Voltage Regulator S7V8F3

3.3V Step-Up/Step-Down Voltage Regulator S7V8F3 The S7V8F3 switching step-up/step-down regula..

£5.88 Ex Tax: £4.90

12V Step-Up/Step-Down Voltage Regulator S10V2F12

12V Step-Up/Step-Down Voltage Regulator S10V2F12

12V Step-Up/Step-Down Voltage Regulator S10V2F12 This switching regulator uses the SEPIC topo..

£4.08 Ex Tax: £3.40

3.3V Step-Up Voltage Regulator U1V10F3

3.3V Step-Up Voltage Regulator U1V10F3

3.3V Step-Up/Down Voltage Regulator U1V10F3 This tiny (0.35″×0.45″) U1V10F3..

£3.54 Ex Tax: £2.95

5V Step-Up Voltage Regulator U1V10F5

5V Step-Up Voltage Regulator U1V10F5

5V Step-Up/Down Voltage Regulator U1V10F5 This tiny (0.35″×0.45″) U1V10F5 s..

£4.14 Ex Tax: £3.45

5V Step-Up Voltage Regulator U3V50F5

5V Step-Up Voltage Regulator U3V50F5

5V Step-Up Voltage Regulator U3V50F5 This powerful boost regulator efficiently generates an o..

£10.68 Ex Tax: £8.90

Adjustable 4V-12V Step-Up Voltage Regulator U3V50ALV

Adjustable 4V-12V Step-Up Voltage Regulator U3V50ALV

Adjustable 4V-12V Step-Up Voltage Regulator U3V50ALV This powerful boost regulator efficientl..

£11.88 Ex Tax: £9.90

12V Step-Up/Step-Down Voltage Regulator S18V20F12

12V Step-Up/Step-Down Voltage Regulator S18V20F12

12V Step-Up/Step-Down Voltage Regulator S18V20F12 This powerful step-up/step-down regulator e..

£13.80 Ex Tax: £11.50

Pololu 5V 5A Step-Down Voltage Regulator D24V50F5

Pololu 5V 5A Step-Down Voltage Regulator D24V50F5

Pololu 5V 5A Step-Down Voltage Regulator D24V50F5 This small synchronous switching step-down ..

£19.14 Ex Tax: £15.95

5V, 500mA Step-Down Voltage Regulator D24V5F5

5V, 500mA Step-Down Voltage Regulator D24V5F5

5V, 500mA Step-Down Voltage Regulator D24V5F5 The compact (13mm × 10mm × 3mm) D24..

£4.20 Ex Tax: £3.50

Pololu 3.3V, 500mA Step-Down Voltage Regulator D24V5F3

Pololu 3.3V, 500mA Step-Down Voltage Regulator D24V5F3

Pololu 3.3V, 500mA Step-Down Voltage Regulator D24V5F3 The compact (13mm × 10mm ×..

£4.20 Ex Tax: £3.50

Pololu 5V 2.5A Step-Down Voltage Regulator D24V22F5

Pololu 5V 2.5A Step-Down Voltage Regulator D24V22F5

Pololu 5V 2.5A Step-Down Voltage Regulator D24V22F5 This small synchronous switching step-dow..

£9.36 Ex Tax: £7.80

4V - 12V Adjustable Step-Up/Step-Down Voltage Regulator S18V20ALV

4V - 12V Adjustable Step-Up/Step-Down Voltage Regulator S18V20ALV

4V - 12V Adjustable Step-Up/Step-Down Voltage Regulator S18V20ALV This powerful step-up/step-..

£12.00 Ex Tax: £10.00

4.5-20V Fine-Adjust Step-Up Voltage Regulator U3V70A

4.5-20V Fine-Adjust Step-Up Voltage Regulator U3V70A

4.5-20V Fine-Adjust Step-Up Voltage Regulator U3V70A This powerful synchronous switching boos..

£15.48 Ex Tax: £12.90

Pololu 4-25V Adjustable Step-down Voltage Regulator D36V6AHV

Pololu 4-25V Adjustable Step-down Voltage Regulator D36V6AHV

Pololu 4-25V Adjustable Step-down Voltage Regulator D36V6AHV This compact (0.4″ ×..

£6.84 Ex Tax: £5.70

5V Step-Up/Step-Down Voltage Regulator S9V11F5S6CMA with cut-off

5V Step-Up/Step-Down Voltage Regulator S9V11F5S6CMA with cut-off

Pololu 5V Step-Up/Step-Down Voltage Regulator S9V11F5S6CMA w/ Adjustable Low-Voltage Cutoff T..

£7.44 Ex Tax: £6.20

Tags: Pololu, 12V, 1A, Step-Down, Voltage, Regulator, D24V10F12, 2834, buck, step, down, Pololu